Introduction of pallet tilter
LT series lift and tilt pallet jack are designed to lift the pallet and tilt it to the ergonomic angle. LT10M manual pallet tilter & LT10E electric pallet tilter are worked to allow the users to ergonomically reach loads easily without having to bend down or over-stretch. The Electric tilt pallet jack has forced steering on one wheel to make manoeuvring easy. Lift /lower functions are controlled by a switch on the control lever. Tilt/return functions are controlled by a remote control, which is fitted with a long wire, and can make the operator and the tilter with load keep a certain distance, more safer. Lift /lower function and Tilt/return functions can be operated independently of each other or simultaneously. When Tilt/return functions are to be used, the tilter must be on a firm surface, and the universal wheel shall be braked. When Tilt/return functions are to be used to stack materials, the handle can be turned to the side to make access to the stack table easier.
As a pallet tilting equipment, this pallet jack tilter can be used as a pallet truck and also a tilting pallet truck, this can not only improve your work efficiency, but also save costs.
手柄可以旋转并锁定在远离工作区域的位置。它适用于坐姿和站立姿势。托盘倾斜千斤顶的前叉最多可倾斜90度。它们都标配了驻车制动器和脚保护器。
符合EN1757-1和EN1175
Details of pallet tilter
LT0M manual pallet tilter LT10E electric pallet tilter
We have this item in stock in France/US, if you are located in Europe or US, we can arrange delivery to you ASAP! This way will save your time and shipping cost.
Specifications of pallet tilter
| 我电梯号 | 1520902 | 1520903 | |
| 模型 | LT10M | LT10E | |
| 类型 | 手册 | 电动 | |
| 容量 | 公斤（磅） | 1000(2200) | |
| 提升高度，垂直 | h毫米（英寸） | 285(11.2) | |
| 最小货叉高度 | h1毫米（英寸） | 85(3.3) | |
| 货叉长度 | 我毫米（英寸） | 800(31.5) | |
| 手柄高度 | L1毫米（英寸） | 1138(44.8) | |
| 货叉总宽度 | b毫米（英寸） | 560(22) | |
| 货叉之间的宽度 | b1毫米（英寸） | 234(9.2) | |
| 滚筒前叉尖长度 | L2毫米（英寸） | 135(5.3) | |
| 整体的宽度 | B毫米（英寸） | 638(25.1) | |
| 总长度 | L毫米（英寸） | 1325(52.2) | 1410(55.5) |
| 整体高度，升高 | 高mm（in。） | 950(37.4) | |
| 整体高度，降低 | 高mm（in。） | 750(29.5) | |
| 负载中心最小/最大 | C1毫米（英寸） | 200/400(8/16) | |
| 负载中心最小/最大 | C2毫米（英寸） | 200/420(8/16.5) | |
| 动力单元 | 功率/功率 | -- | 0.8/12 |
| 净重 | 公斤（磅） | 178(391.6) | 185(407) |
安全守则
1. Driving the pallet tilter on the slope
1) The pallet tilter shall be unloaded or a small load.
2）负载应位于最低位置。
3) The gradient shall be no more than 2° when dragging the pallet tilter.
4）无论是升级还是降级，操作员均应处于较高位置。
2. Avoid offset loads
负载必须均匀分布在货叉或货盘上，重心与货叉前部之间的距离为400mm，最大重心高度为420mm，最小为200mm，超出此范围的距离将降低安全，增加风险。
托盘或货叉上的货物必须妥善固定，避免负载不平衡，以免在运输过程中，叉车抬升或叉车必须保持抬高一段时间的情况下掉落。
3. Driving loaded
The tilting pallet jack is designed for use on even and level floor. During transport the forks shall be raised as little as possible. Transport with raised forks should be made over the shortest possible distances and at low speed. Do not transport when tilting goods on the pallet tilter, this is not safe.
警告： 切勿将手或脚放在活动部件上，否则有受伤危险。
